1. Heat and airflow
The metal enclosure relies on convection cooling. Avoid assuming the full rated output remains available inside a hot or poorly ventilated cabinet. Use the datasheet derating curves and installation instructions.

24V DC · 2.2A · 52.8W enclosed switching power supply
Explore the specifications, calculate your load, understand installation constraints, and compare alternatives before requesting a quote from ANB Electronics in Thailand.
Stock quantity and delivery timing are confirmed when you inquire.

Values below are for the LRS-50-24 variant, not every member of the LRS-50 family. Confirm the latest manufacturer revision before final design approval.
| AC input range | 85–264 VAC, 47–63 Hz |
|---|---|
| Typical efficiency | 88% |
| Output adjustment | 21.6–28.8 V |
| Ripple and noise (max.) | 150 mVp-p (datasheet test conditions) |
| Voltage tolerance | ±1.0% |
| Protection | Short circuit, overload, overvoltage |
| Dimensions | 99 × 82 × 30 mm |
|---|---|
| Cooling | Free-air convection; no fan |
| Working temperature | −30°C to +70°C, subject to derating |
| Humidity | 20–90% RH, non-condensing |
| Output indicator | Power-on LED |
| Manufacturer-listed warranty | 3 years (verify current terms) |
Source: Manufacturer Datasheet Approval status and specifications are subject to change; verify against current manufacturer documents.
Use this quick calculator for a steady-state 24V load. It checks rated output current and a user-selected design margin; it does not establish suitability under startup surge, temperature derating, low input voltage or transient loads.
All three examples below have 24V output variants. Ratings are nominal and subject to each model's own datasheet and derating limits.
| Model | Rated output | Best reason to consider it | Next step |
|---|---|---|---|
| LRS-35-24 | 24V · 1.5A · 36W | Lower-current loads where its rated capacity is sufficient. | Manufacturer Datasheet |
| LRS-50-24 | 24V · 2.2A · 52.8W | Compact choice for loads within its verified electrical and thermal limits. | Check load |
| LRS-100-24 | 24V · 4.5A · 108W | More output capacity for higher loads or greater design headroom. | Manufacturer Datasheet |
The comparison is for initial screening. Verify exact model specifications, mounting clearances, operating conditions and suitability in each linked datasheet.
The metal enclosure relies on convection cooling. Avoid assuming the full rated output remains available inside a hot or poorly ventilated cabinet. Use the datasheet derating curves and installation instructions.
Steady-state wattage alone can be misleading. Solenoids, motors and loads with large input capacitors may draw substantially more current during startup; confirm actual peak requirements.
Verify AC input suitability, protective earth, conductor sizing, overcurrent protection and terminal arrangements using the manufacturer's current instructions and local electrical requirements.
The LRS-50-24 is an enclosed component power supply, not a ready-to-install consumer appliance. Qualified personnel must assess shock protection, enclosure, spacing, EMC and end-equipment compliance. Never work on energized mains terminals.
For the 24V variant, the manufacturer lists 24V × 2.2A = 52.8W. The LRS-50 family designation is not a substitute for the exact variant's rated output.
A 1.8A steady load uses about 82% of the 2.2A rating. With a 20% spare-capacity target, the required current is 2.16A—just under the nominal rating. Startup peaks and derating still need evaluation.
No. The specified operating range refers to permitted operation subject to derating. Review the temperature and input-voltage derating curves for the actual installation.
The datasheet lists a 21.6–28.8V adjustment range for this variant. Adjustment must respect the connected equipment's voltage limits and the manufacturer's operating instructions.
It is the manufacturer's maximum peak-to-peak output ripple/noise figure under stated test conditions. Sensitive analog, measurement or RF loads may require additional assessment or filtering.
ANB offers product-selection assistance, installation guidance and troubleshooting support. Share your load, input supply, environment and symptoms when requesting help.
Tell us the quantity required, load current, ambient temperature, input supply and intended application. We can discuss selection, installation and troubleshooting, and confirm available stock and delivery timing.
Request LRS-50-24 quote →